Quantcast
Channel: electro-music.com -> The layout factory
Browsing all 621 articles
Browse latest View live
↧

RYO 3x VCA - Stripboard layout help

Hi Nardu - Greetings and thank you for your generosity sharing these! :lol:

View Article


RYO 3x VCA - Stripboard layout help

So you do not miss any spilt points, use this helper. Print from ryo 2x vca_v.3 split points helper.pdf file to 1:1 scale , crop to edges and stick the corners on bottom side. Note! For any prints for...

View Article


RYO 3x VCA - Stripboard layout help

Very helpful thank youUnfortunately have to change heating element in soldering iron before can do any more circuits! Have replacement hope repair goes well!

View Article

RYO 3x VCA - Stripboard layout help

Use TL074 both, has lower noise figure.

View Article

RYO 3x VCA - Stripboard layout help

Analyzing the circuit RYO VCA , LM324 (cheaper) is used for CV, work with DC; is not critical. TL084 works with audio and the noise figure (NF) is important; affects the signal-to-noise ratio (SNR)....

View Article


APC BUILD Help

And one more error: out should be VR4-2Oh and the components names don't match:VR1 = R2, VR2 = R3, VR3 = R4C3 is backwards :roll:

View Article

APC BUILD Help

Hi Project 2501 - There is some cool "Appleseed" anime too :) I regularly listen to John Coltrane and Miles Davis and such but don't know much about jazz especially good newer stuff. Did go to a Snarky...

View Article

TR-808 Snare Stripboard

I've just finished building the 808 snare to complement the other fantastic Eric Archer kick and hats modules.The snare works ok initially and triggers fine but for some reason after a few minutes...

View Article


RYO 3x VCA - Stripboard layout help

nice one!

View Article


RYO 3x VCA - Stripboard layout help

Din't expect to see so much effort! You'r a king Nardu! 8)

View Article

RYO 3x VCA - Stripboard layout help

With potential, Otto's Eurorack modules - Stripboard-480 version

View Article

Midi to CV Layout :)

https://obsoletetechnology.wordpress.com/projects/midi-cvgate-converter/i have build two of them

View Article

MS-20 VCF Stripboard Layout

I've been looking around for an MS-20 VCF layout for awhile. I've seen acouple but none of them verified or have clear directions, especially on potentiometer wiring. Does anyone have a verified...

View Article


MS-20 VCF Stripboard Layout

Thank you so much for posting this! :lol: Does anyone the Res. Potentiometer value? 100k log maybe? Also, is that switch a DPDT ON-OFF-ON switch? Is that for LP/HP? [/b]

View Article

MS-20 VCF Stripboard Layout

In the original schematic the reso pot is 10k. However i once build this and made a dual Version, both switchable between LPF and HPF and able to work as two separate VCF's and wasn't really happy with...

View Article


MS-20 VCF Stripboard Layout

First add some 10R resistors and decoupling caps on the power rails, also use decoupling caps for the LM13700 and place them as close to it's rails as possible. perhaps move that one resistor leg away...

View Article

MS-20 VCF Stripboard Layout

Hi, thanks for finding those kind words for my attempts at being somewhat musical :lol: My neighbours think otherwise... i'm not sure what you mean with the bottom resistor.what i meant, was moving R18...

View Article


Cloning the CR78 with MIDI

I got something very similar to the posted Metallic Beat circuit to work, by lowering the value of R566. Someone in the thread mentioned that the trigger pulse was -15V, I think that's the problem; the...

View Article

Craig Anderton Hip Bass Drum PCB

Hi guys!Noob question, but whitout it I could not learn.Could the hip bass drum work under +/-9v without any adaptation, and will it sound the same?Thank's.

View Article

WASP vcf stripboard

Hi.I want to add a Wasp vcf to my modular rig, but i feel lazy and i don't want to etch a PCB for it.I've been searching for a stripboard layout and i'm surprised to not find even one.It's odd for such...

View Article
Browsing all 621 articles
Browse latest View live